6 Ways to Heat Set Your Screen Printing Ink

Jul 10, 2019 | Cricut Projects, Heat Setting, Screen Printing, Tutorials

This post may contain Amazon or other affiliate links. If you purchase something through the link, I may receive a small commission at no extra charge to you.

How to heat set speedball fabric inkLast week, I shared a tutorial explaining how to heat set Speedball Fabric Ink using an Easy Press 2 from Cricut. Many of you asked if there were other ways to heat set the ink to make it permanent and washable.  While I had heard of many different ways to heat set ink, I wanted to test them out before giving any recommendations.  What better way than to do a little heat setting experiment of my own!

The Heat Setting Experiment

To start this experiment, I screen printed the same design on 6 tea towels using Speedball black fabric ink.  After allowing them all to dry overnight, I used a different method of heat setting for each towel. Keep reading to find out how each method held up after going through the wash a couple of times.

6 ways to heat set screen printing ink water based

  1. Heat Press
  2. Easy Press 2
  3. Basic Household Iron
  4. Clothes Dryer
  5. Kitchen Oven
  6. Heat Gun

The Results

The “before” picture shows the dry ink – before the towel went through the wash.  The “after” shows the same towel – after it was washed twice.

1 : Heat Press

Heat set screen printing with heat press
The heat press is one of my favorite craft tools. After years of HTV, I now use the heat press in a different way… to heat set screen printing ink.  I love using the heat press because I can fit my entire design under the heat. This means just one 40 second press and I’m ready to press my next item.

PROCEDURE: Set heat press to 320 degrees and press for 40 seconds. That’s it… it can now go in the wash.

✅ RESULT: After washing the towel twice, the ink did not fade.

2 : Easy Press 2

Heat set screen printing easy press 2

If you are a Cricut fan, you may have the Easy Press 2. This is a great way to heat press shirts. I have 2 different sizes – the smaller one works great for smaller projects or pocket designs and the larger Easy Press 2 is perfect for large designs.

PROCEDURE: Set Easy Press 2 to 320 degrees and press for 40 seconds. Repeat the process (if necessary) until you have applied heat to your entire design.  That’s it… it can now go in the wash.

✅ RESULT: After washing the towel twice, the ink did not fade.

3 : Basic Household Iron

Heat set screen printing with iron

Not ready to invest in a Heat Press or Easy Press 2?  You can start screen printing with a basic household iron. If your iron doesn’t cover your entire design, you’ll need to move your iron around the design to ensure every part is heated.

PROCEDURE:  Set iron on cotton setting (or match your material). Cover the design with parchment paper and iron over the entire design for 3-5 minutes, moving the iron constantly.

✅ RESULT: After washing the towel twice, the ink did not fade.

4 : Dryer

Can you heat set screen printing in in dryer

I had always heard that you can heat set in the dryer but I hadn’t tried it until this experiment. It seems like a convenient method if you are doing a large quantity of shirts, so I wanted to give it a shot.

PROCEDURE: After allowing the ink to air dry overnight, I put the towel directly in my household dryer on high heat for a timed dry of 40 minutes.  After heating the towel in the dryer for one 40 minute cycle, I did the wash test.

❌ RESULT: After washing the towel once, I noticed some fading. After the second time in the wash, it faded substantially. I believe this method could work with longer time in the dyer. However, more than 40 minutes in the dryer didn’t seem very practical to me so I didn’t try this test again.  If you plan to try this method, you definitely want to heat set in the dryer longer than 40 minutes.

5 : Kitchen Oven

Heat set screen printing with oven

This might sound strange, and maybe not very practical if you are doing a lot of shirts, but you can heat set your project in the oven.  I put the towel on a cookie sheet lined with parchment paper to keep the towel from touching the bottom of the oven and burning.

PROCEDURE: Preheat oven to 400 degrees. Place the towel in the oven and immediately turn off the heat. Allow it to stay in oven for 10 minutes.

✅ RESULT: After washing the towel twice, the ink did not fade.

6 : Heat Gun

Heat set screen printing with heat gun

I purchased a heat gun to speed up the ink drying process when using my screen printing press. I wanted to experiment to see if I could heat set the ink with the heat gun as well.

While it did work, there was one spot that I got a little too close to the material and it started to burn.  If you look close, you’ll see some faint burn marks on the white material around the “est 2005” part of the design. This could be prevented by keeping the heat gun a little further away from the material and moving it around constantly (like a hair dryer).

PROCEDURE: Set heat gun to high heat setting and move back and forth over design for 1-2 minutes, about 4-5 inches away from the material. Be sure not to leave the heat gun in one place too long or it will burn your material!

✅ RESULT: After washing the towel twice, the ink did not fade.


I’m excited to report that you can use a heat press, Easy Press 2, household iron, oven, or heat gun to get good results with your Speedball Fabric ink.

My method of choice will still be the heat press or Easy Press 2 because they are the quickest. It’s also helpful that I can ensure even heat over the entire design in just one press.

If you are screen printing at home or just starting your small business, you may not be ready to add extra equipment like the Easy Press 2 or a standard heat press.  If that’s the case, try your iron or oven!

how to screen print with craft vinyl pigskins and pigtails


  1. Thanks for sharing your talents with us! You’re awesome!

    • Thanks so much! I’m enjoying sharing this craft with fellow creatives!

    • When using the cricuit heat press to you place it directly on the design or should you put a paper in between?

      • I’ve done it both ways. Out of habit, I tend to put a piece of parchment paper or teflon down. I haven’t ever had issues with the ink sticking or transferring but that would be the only reason you would want to put something between.

        • Hey there,
          Does the fry time effect if the shirt will fade or not? I have a few shirts that the design has faded some after 2 washes! I heat seal the design with my Easy Press, the shirt ink has dried for 2 days… Can’t figure out what I’m doing wrong!
          ( I’m using speedball fabric ink).

          • It could be that the shirt didn’t get dry enough. Make sure you have good ventilation. A fan can help with that! You can also try pressing the shirt twice (lift it up in between so it releases the heat) just to be sure it’s getting heated long enough.

      • Hello! So High temperature! I thought It needs just 160 degree to be cured! Thanx a lot (I will try with my newly buy heat press)

        • Yes! I’ve found 320 is the sweet spot for me, but definitely adjust if you find something that works better for you!

  2. Wow, thanks for this information. It’s always good to know if something works so a project doesn’t get ruined.

    • I’m so glad you found this helpful! I’m always willing to try and see what works! Let me know if there are any questions you have..I’m always looking for the next experiment!

      • Is the 320 degrees for 40 seconds for all tshirt blends? Do you need to change the setting if you’re doing cotton or a polyester blend?

  3. Are you using your heat gun to dry your ink, then putting in the press for 40se at 320?


    • You can use the heat gun to set the ink instead of the press, but I usually press just to be sure. It’s hard to tell if you covered all of the ink when using the heat gun. If you miss a spot, that part may fade. I usually just use the heat gun to speed up drying between layers of ink or when I’m doing multi-color shirts.

  4. Do you know if there is a time limit on when you have to heat the design? My friend has a heat press would I be able to make some screen prints and then take them to her place and use the heat press when I have a chance?

    • No time limit.. in fact, the longer you let the shirts air dry before heat setting, the better!

    • I printed a design on cotton fabric from my printer. I heat set it a couple of times on Cotton setting. I tried washing it today and the colors ran. What did I do wrong and how can it keep it from running?

  5. Great info thank you! Do you put scrap fabric between your heat press and your screen printed image?

    • never mind just read some of the additional comments. Thank you!

  6. Thank you!!! Your videos are incredibly helpful and your work is motivating!!

  7. Do you need to wait 24-48 hrs for the ink to dry to then use the Heat Press? I have been using the Cricut Easy Press…..but I think I want something bigger and faster. But I am not ready to purchase the Flash dryer.

    • Whether you use a heat press or EasyPress, the drying time is the same. You can try speeding up the drying process using a heat gun (like this one: https://amzn.to/2ZKPzmQ). The flash dryer dries and heat cures all in one.. and since it covers the entire shirt, you know it’s getting heated evenly. But, yes, it’s a pretty big investment to make just to speed up the process!

  8. Hi! If you mess up, how easy is it to get the ink off before you hear set it?

  9. I know you’ve said in other comments to let the garment air day and then use the EasyPress. However, have you used the Easy press right away? Would that not be recommended?

  10. Do you have videos on the whole process? I tried the infused ink sheets and they faded after the first wash.

  11. Your tutorials and blog have been a valuable tool for this newbie to screen printing! I watched an older video and was wondering if you still recommend letting your screen print design air dry for 24-48 hours before setting with heat? What I’m trying to figure out is how to handle pressing multiple shirts and what to do with them as they are air drying, so you can continue using your screen press. I hope that makes sense. Thank you in advance!

    • I’m so glad to hear you’ve gotten started screen printing! When I print a bunch of shirts, I lay them all over the room – backs of chairs, table, floor – to let them dry. It is important to let them dry properly or the ink will fade when you wash them. If you have a heat gun or fan, that will speed up the process a bit. Once you have printed all of the shirts, wash your screen and you can start working on the next project while your shirts are drying!

  12. I’m using speedball ink and I have a heat press. I did a couple hoodies. The design is very thick. I’ve been letting it dry for a few days. Does the thickness/ size of the design determine how long to press it? Or should I still stick to 320 for 40secs?

  13. Hi and Thank you for all of your wonderful information here! If I have a heat gun and use that to speed up the drying of my Speedball Ink, do I still need to wait to heatpress or can I do that immediately after the heat gun? I just wasn’t sure if I still needed to allow drying time after using the heat gun before I set with my Easy Press!?

  14. What temp & how long to heatset on heat press 100% polyester?

  15. thank you SO MUCH for sharing your methods and results! I’m a micro batch printer just learning and experimenting with painting with Speedball screen printing inks. I’m typing this up as my recent prints are heating in the oven…. your article is so helpful and interesting!

    • Hey Kristina! Thanks for taking the time to leave a comment. It means a lot to hear feedback from a fellow printer! I hope your project turned out great!

    • Dean and Kristina,

      In the same boat doing small batches! Thanks for the all the help. For the oven, have you found that all the design has to be visible, or could you roll a tea towel up and assume the heat gets into the middle layers?

  16. Do you think the heat gun method would work for water bottles such as a yeti or hydroflask?

  17. thanks for your interesting report about the printing process. Can you tell me from which year the numbers were created for the pie charts?


Leave a Reply to Jennifer Cancel reply

Your email address will not be published. Required fields are marked *

Want to get the latest screen printing tips and tricks delivered to your inbox?

Join my email list and be the first to know about new techniques and project ideas!